EXAMPLE AT A GLANCE
This fictional Newcastle, New South Wales rangehood installation example contains 7 itemised costs totalling A$2,021.26. Its app-exported PDF uses the exact metric quantities and AUD rates in the table, with scope assumptions and exclusions explained below.
Project scope: One hood above existing cooker
Replace one kitchen extraction hood using a selected unit and an existing suitable duct and electrical supply. Include removal, mounting, connection and operation check.
This original fictional example is set in Newcastle, New South Wales. Harbour & Gum Projects and Alex Morgan are made-up parties. The matching Australian guide explains which measurements, product decisions and site conditions turn this brief into a client-ready quote.
- Example location
- Newcastle, New South Wales
- Prepared by
- Harbour & Gum Projects · fictional business
- Prepared for
- Alex Morgan · fictional customer
- Issued / valid through
- 25 September 2026 / 25 October 2026
Itemised rangehood installation costs
These 7 AUD lines reproduce the native app export. Existing hood removal is measured as 1 each; Hood product allowance uses 1 each. Some lines are measured work while others are a product or site-task allowance. Read the unit before reusing the structure for a different job.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Site and connection check | 1 job | A$158.13 | A$158.13 |
| Existing hood removal | 1 each | A$192.50 | A$192.50 |
| Hood product allowance | 1 each | A$742.50 | A$742.50 |
| Duct transition allowance | 1 set | A$165.00 | A$165.00 |
| Mount and secure hood | 1 each | A$398.75 | A$398.75 |
| Connection and airflow check | 1 job | A$233.75 | A$233.75 |
| Disposal and cleanup | 1 job | A$130.63 | A$130.63 |
| Illustrative total | A$2,021.26 | ||
Product selection and installation should be clear from the descriptions. Confirm delivery, fixings, preparation, waste and any specialist trade responsibility for the actual job rather than assuming each allowance covers them.
Check the arithmetic
Existing hood removal: 1 each × A$192.50 = A$192.50. Hood product allowance: 1 each × A$742.50 = A$742.50. All other lines use the same quantity-by-rate calculation and sum to A$2,021.26. Every fixture line lands on an exact cent, so the native PDF subtotal equals the displayed table total.
Measurement to check: Measure opening width, mounting height, duct route and available power before ordering. Selection to check: Show the hood product and transition fittings separately from mounting labour. The PDF uses a 0% tax input only to make its fictional arithmetic visible. Confirm the GST treatment that applies to the actual job and set your own markup before sharing a client quote.
Assumptions and exclusions
Check cabinet clearances and isolate power before removal; verify the chosen unit fits the existing outlet.
Outside this stated scope: No new external vent, electrical circuit, cabinet rebuild or wall finish repair.
An absent duct, unsuitable wiring or cabinet modification requires a separately scoped trade visit. A changed condition should lead to a newly measured quantity, revised allowance or separately agreed task. Keep the client informed of the changed figure before producing another PDF.
Open the app-exported PDF
The document was exported from Estimates using the fictional business, client, dates, short PDF scope, notes and cost lines shown here. The image is the first-page preview. Open the complete PDF to check all entries; no rate is a current Newcastle, New South Wales market claim.
Adapt this example to a real job
- Write the actual work boundary and site address; use this measurement basis: Measure opening width, mounting height, duct route and available power before ordering.
- Confirm products, access and handoff responsibilities; record this selection decision: Show the hood product and transition fittings separately from mounting labour.
- Replace all fictional product, labour and subcontractor rates with your own evidence.
- Review quantities, extensions, total, GST and markup settings, client details and validity date.
- Preview every PDF page and share the quote with the agreed exclusions.
- Measure opening width, mounting height, duct route and available power before ordering.
- Show the hood product and transition fittings separately from mounting labour.
- Check cabinet clearances and isolate power before removal; verify the chosen unit fits the existing outlet.
- An absent duct, unsuitable wiring or cabinet modification requires a separately scoped trade visit.
Read the paired estimating guide for the project-specific scope and work sequence.
Questions about this estimate
Which quantity controls this rangehood installation estimate?
Measure opening width, mounting height, duct route and available power before ordering.
When should this rangehood installation quote be revised?
An absent duct, unsuitable wiring or cabinet modification requires a separately scoped trade visit. No new external vent, electrical circuit, cabinet rebuild or wall finish repair.
TURN THE SCOPE INTO AN ITEMISED PDF
Make your own rangehood installation estimate.
Describe the actual job in Estimates on iPhone or Android or use AI assistance to start a draft. Check every measurement, quantity, rate, allowance, client detail and note before exporting your PDF. Some app features may require an in-app purchase.
