THE ESTIMATING ANSWER
For one two-wall garage storage run, start with a defined scope and measurement basis. Measure clear wall runs, floor slope, door sweep and storage loads. Separate selected cabinets, shelf rails and countertop from fitting labour. Price the listed tasks separately and state the condition that would require a revision: Hidden services or insufficient backing change anchors and cabinet positions.
This guide uses a fictional project in Saskatoon, Saskatchewan: One two-wall garage storage run. Its matching estimate and PDF give each scope decision a visible CAD cost line. Use the document to understand the structure; verify the actual building, product schedule, labour and supplier inputs before preparing a client quote.
1. Define the measured job
Fit modular shelves, cabinets and a work surface along two sound garage walls while retaining vehicle clearance. Measure clear wall runs, floor slope, door sweep and storage loads. Record the measurements and existing condition in the estimate before turning quantities into line items. The scope should make clear why this is a separate project from a broader renovation or maintenance quote.
Measurement basis: Measure clear wall runs, floor slope, door sweep and storage loads.
2. Build a product and labour schedule
Separate selected cabinets, shelf rails and countertop from fitting labour. This example has 7 distinct lines, including garage layout and protection, wall-rail allowance, cabinet allowance. Use actual supplier prices and labour inputs for a customer job; the displayed amounts are fictional document inputs.
Selections to confirm: Separate selected cabinets, shelf rails and countertop from fitting labour.
3. Sequence the work and handoffs
Lay out storage at full scale before fixing to suitable backing. Show which task depends on access, a selected product or another trade. If that dependency is still open, label the price preliminary and identify the information needed before a firm quote.
Work sequence: Lay out storage at full scale before fixing to suitable backing.
4. Set a change boundary
Hidden services or insufficient backing change anchors and cabinet positions. The example excludes electrical work, floor coating or structural wall reinforcement. Record the discovery, agree the revised work and update the estimate before adding it to the job.
If the job changes: Hidden services or insufficient backing change anchors and cabinet positions.
Review the Canadian job address
Inspect the existing substrate, access and product selections at the property. Check any local trade or municipal requirements that apply and record unresolved conditions before preparing the final client document.
The wall-rail allowance line uses 30 linear ft., approximately 9.14 m. Check the route, cuts and supplier unit before setting a real quantity. The example amounts are fictional CAD document inputs, not current rates for Saskatoon, Saskatchewan or another community. A site visit and current supplier information are needed to replace them.
Work through the itemized calculation
Check each extension of quantity and rate in the paired PDF. Two lines from this project are:
- Wall-rail allowance: 30 linear ft. × C$38.00 = C$1,140.00.
- Cabinet allowance: 3 each × C$430.00 = C$1,290.00.
Adding all 7 rounded line amounts gives C$7,209.00. The PDF shows 0% tax and the same total before any markup. The sample shows 0% tax only to make the arithmetic visible. Determine any applicable GST, HST or PST and markup for the actual work before sharing a quote.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Garage layout and protection | 1 job | C$270.00 | C$270.00 |
| Wall-rail allowance | 30 linear ft. | C$38.00 | C$1,140.00 |
| Cabinet allowance | 3 each | C$430.00 | C$1,290.00 |
| Shelf material allowance | 38 linear ft. | C$43.00 | C$1,634.00 |
| Countertop allowance | 8 linear ft. | C$120.00 | C$960.00 |
| Storage fitting labour | 18 hours | C$95.00 | C$1,710.00 |
| Level check and cleanup | 1 job | C$205.00 | C$205.00 |
| Illustrative subtotal | C$7,209.00 | ||
Scope and pricing boundaries
Fit modular shelves, cabinets and a work surface along two sound garage walls while retaining vehicle clearance.
Outside this example: No electrical work, floor coating or structural wall reinforcement.
Keep the product allowance, installation work and any unresolved condition visible as separate decisions. If access or the selected product changes, update the affected quantity or rate and explain the revision before the client relies on the estimate.
Before you send the estimate
- Measure clear wall runs, floor slope, door sweep and storage loads.
- Separate selected cabinets, shelf rails and countertop from fitting labour.
- Lay out storage at full scale before fixing to suitable backing.
- Hidden services or insufficient backing change anchors and cabinet positions.
Check the business, client, property, dates, line extensions and notes. The garage wall storage fitout PDF example shows one way to present them. Its short PDF note lists the brief's scope exclusions; the fuller project limits above should guide your own scope.
Questions about this estimate
Which quantity controls this garage wall storage fitout estimate?
Measure clear wall runs, floor slope, door sweep and storage loads.
When should this garage wall storage fitout quote be revised?
Hidden services or insufficient backing change anchors and cabinet positions. No electrical work, floor coating or structural wall reinforcement.
MAKE THE NEXT ESTIMATE YOUR OWN
Build a garage wall storage fitout estimate.
Enter the job scope in Estimates on iPhone or Android or start from an AI-assisted draft. Check every quantity, rate, allowance, client detail and note before exporting the PDF. Some app features may require an in-app purchase.
