THE ESTIMATING ANSWER
For one interior doorway, start with a defined scope and measurement basis. Measure opening, wall thickness, travel space and hidden service routes. Identify pocket frame, door leaf and hardware separately. Price the listed tasks separately and state the condition that would require a revision: Load-bearing framing or pipes inside the pocket zone require redesign.
This guide uses a fictional project in Halifax, Nova Scotia: One interior doorway. Its matching estimate and PDF give each scope decision a visible CAD cost line. Use the document to understand the structure; verify the actual building, product schedule, labour and supplier inputs before preparing a client quote.
1. Define the measured job
Install one pocket sliding door kit within a defined non-load-bearing interior partition, with track, door leaf and finish trim. Measure opening, wall thickness, travel space and hidden service routes. Record the measurements and existing condition in the estimate before turning quantities into line items. The scope should make clear why this is a separate project from a broader renovation or maintenance quote.
Measurement basis: Measure opening, wall thickness, travel space and hidden service routes.
2. Build a product and labour schedule
Identify pocket frame, door leaf and hardware separately. This example has 7 distinct lines, including opening and service survey, partition opening, pocket frame allowance. Use actual supplier prices and labour inputs for a customer job; the displayed amounts are fictional document inputs.
Selections to confirm: Identify pocket frame, door leaf and hardware separately.
3. Sequence the work and handoffs
Confirm wall construction and services before opening the partition. Show which task depends on access, a selected product or another trade. If that dependency is still open, label the price preliminary and identify the information needed before a firm quote.
Work sequence: Confirm wall construction and services before opening the partition.
4. Set a change boundary
Load-bearing framing or pipes inside the pocket zone require redesign. The example excludes structural wall alteration, electrical relocation or whole-room repainting. Record the discovery, agree the revised work and update the estimate before adding it to the job.
If the job changes: Load-bearing framing or pipes inside the pocket zone require redesign.
Review the Canadian job address
Inspect the existing substrate, access and product selections at the property. Check any local trade or municipal requirements that apply and record unresolved conditions before preparing the final client document.
Count the actual units, site visits and selected products separately. A count in this example is a document input, not a substitute for inspecting the real property. The example amounts are fictional CAD document inputs, not current rates for Halifax, Nova Scotia or another community. A site visit and current supplier information are needed to replace them.
Work through the itemized calculation
Check each extension of quantity and rate in the paired PDF. Two lines from this project are:
- Pocket frame allowance: 1 each × C$900.00 = C$900.00.
- Door and hardware allowance: 1 set × C$1,005.00 = C$1,005.00.
Adding all 7 rounded line amounts gives C$5,025.00. The PDF shows 0% tax and the same total before any markup. The sample shows 0% tax only to make the arithmetic visible. Determine any applicable GST, HST or PST and markup for the actual work before sharing a quote.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Opening and service survey | 1 job | C$305.00 | C$305.00 |
| Partition opening | 1 job | C$690.00 | C$690.00 |
| Pocket frame allowance | 1 each | C$900.00 | C$900.00 |
| Door and hardware allowance | 1 set | C$1,005.00 | C$1,005.00 |
| Frame and track fitting | 1 job | C$1,035.00 | C$1,035.00 |
| Wall board and trim closure | 1 job | C$850.00 | C$850.00 |
| Adjustment and cleanup | 1 job | C$240.00 | C$240.00 |
| Illustrative subtotal | C$5,025.00 | ||
Scope and pricing boundaries
Install one pocket sliding door kit within a defined non-load-bearing interior partition, with track, door leaf and finish trim.
Outside this example: No structural wall alteration, electrical relocation or whole-room repainting.
Keep the product allowance, installation work and any unresolved condition visible as separate decisions. If access or the selected product changes, update the affected quantity or rate and explain the revision before the client relies on the estimate.
Before you send the estimate
- Measure opening, wall thickness, travel space and hidden service routes.
- Identify pocket frame, door leaf and hardware separately.
- Confirm wall construction and services before opening the partition.
- Load-bearing framing or pipes inside the pocket zone require redesign.
Check the business, client, property, dates, line extensions and notes. The pocket sliding door installation PDF example shows one way to present them. Its short PDF note lists the brief's scope exclusions; the fuller project limits above should guide your own scope.
Questions about this estimate
Which quantity controls this pocket sliding door installation estimate?
Measure opening, wall thickness, travel space and hidden service routes.
When should this pocket sliding door installation quote be revised?
Load-bearing framing or pipes inside the pocket zone require redesign. No structural wall alteration, electrical relocation or whole-room repainting.
MAKE THE NEXT ESTIMATE YOUR OWN
Build a pocket sliding door installation estimate.
Enter the job scope in Estimates on iPhone or Android or start from an AI-assisted draft. Check every quantity, rate, allowance, client detail and note before exporting the PDF. Some app features may require an in-app purchase.
