THE ESTIMATING ANSWER
For one new utility-room sink, start with a defined scope and measurement basis. Measure sink footprint, service route, fixing support and working clearance. Separate sink, tap and connection materials from fit-out labour. Price the listed tasks separately and state the condition that would require a revision: Hidden piping or weak wall support can change the mounting method.
This guide uses a fictional project in St. John’s, Newfoundland and Labrador: One new utility-room sink. Its matching estimate and PDF give each scope decision a visible CAD cost line. Use the document to understand the structure; verify the actual building, product schedule, labour and supplier inputs before preparing a client quote.
1. Define the measured job
Install one selected utility sink near existing suitable water and drain services, with tap, trap and wall or floor support. Measure sink footprint, service route, fixing support and working clearance. Record the measurements and existing condition in the estimate before turning quantities into line items. The scope should make clear why this is a separate project from a broader renovation or maintenance quote.
Measurement basis: Measure sink footprint, service route, fixing support and working clearance.
2. Build a product and labour schedule
Separate sink, tap and connection materials from fit-out labour. This example has 7 distinct lines, including site measurement and protection, sink product allowance, tap allowance. Use actual supplier prices and labour inputs for a customer job; the displayed amounts are fictional document inputs.
Selections to confirm: Separate sink, tap and connection materials from fit-out labour.
3. Sequence the work and handoffs
Confirm drain fall and shutoff before fixing the sink. Show which task depends on access, a selected product or another trade. If that dependency is still open, label the price preliminary and identify the information needed before a firm quote.
Work sequence: Confirm drain fall and shutoff before fixing the sink.
4. Set a change boundary
Hidden piping or weak wall support can change the mounting method. The example excludes new room drainage, cabinet fitout or floor repair. Record the discovery, agree the revised work and update the estimate before adding it to the job.
If the job changes: Hidden piping or weak wall support can change the mounting method.
Review the Canadian job address
Verify the existing water, waste and fixture connections on site. Confirm who handles any required trade work, approvals and inspections for this address; this fictional document does not decide them.
Count the actual units, site visits and selected products separately. A count in this example is a document input, not a substitute for inspecting the real property. The example amounts are fictional CAD document inputs, not current rates for St. John’s, Newfoundland and Labrador or another community. A site visit and current supplier information are needed to replace them.
Work through the itemized calculation
Check each extension of quantity and rate in the paired PDF. Two lines from this project are:
- Sink product allowance: 1 each × C$470.00 = C$470.00.
- Tap allowance: 1 each × C$215.00 = C$215.00.
Adding all 7 rounded line amounts gives C$2,020.00. The PDF shows 0% tax and the same total before any markup. The sample shows 0% tax only to make the arithmetic visible. Determine any applicable GST, HST or PST and markup for the actual work before sharing a quote.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Site measurement and protection | 1 job | C$160.00 | C$160.00 |
| Sink product allowance | 1 each | C$470.00 | C$470.00 |
| Tap allowance | 1 each | C$215.00 | C$215.00 |
| Waste and supply fittings | 1 job | C$265.00 | C$265.00 |
| Support and mounting | 1 job | C$335.00 | C$335.00 |
| Water and drain connection | 1 job | C$430.00 | C$430.00 |
| Leak check and cleanup | 1 job | C$145.00 | C$145.00 |
| Illustrative subtotal | C$2,020.00 | ||
Scope and pricing boundaries
Install one selected utility sink near existing suitable water and drain services, with tap, trap and wall or floor support.
Outside this example: No new room drainage, cabinet fitout or floor repair.
Keep the product allowance, installation work and any unresolved condition visible as separate decisions. If access or the selected product changes, update the affected quantity or rate and explain the revision before the client relies on the estimate.
Before you send the estimate
- Measure sink footprint, service route, fixing support and working clearance.
- Separate sink, tap and connection materials from fit-out labour.
- Confirm drain fall and shutoff before fixing the sink.
- Hidden piping or weak wall support can change the mounting method.
Check the business, client, property, dates, line extensions and notes. The utility sink installation PDF example shows one way to present them. Its short PDF note lists the brief's scope exclusions; the fuller project limits above should guide your own scope.
Questions about this estimate
Which quantity controls this utility sink installation estimate?
Measure sink footprint, service route, fixing support and working clearance.
When should this utility sink installation quote be revised?
Hidden piping or weak wall support can change the mounting method. No new room drainage, cabinet fitout or floor repair.
MAKE THE NEXT ESTIMATE YOUR OWN
Build an utility sink installation estimate.
Enter the job scope in Estimates on iPhone or Android or start from an AI-assisted draft. Check every quantity, rate, allowance, client detail and note before exporting the PDF. Some app features may require an in-app purchase.
