EXAMPLE AT A GLANCE
This Brighton example prices two fitted wardrobe shelving layouts with 7 itemised lines and a £1,810.12 illustrative total. It uses fictional prices, a 0% tax input and no markup; verify all inputs for an actual job.
A defined built-in wardrobe shelving installation job
This fictional project is located in Brighton. Install two selected reach-in wardrobe shelving systems in suitable existing wall framing. Include measurement, product allowance for four shelf runs and two hanging rods, wall layout, installation labour, limited wall touch-up and clean-up. No wardrobe door or electrical work. The written scope is the boundary of the example: a customer should be able to match each planned task to a line in the document, and see where a product choice or hidden condition still needs checking.
- Prepared by
- Cedar & Beam Builders · fictional business
- Prepared for
- Jordan Taylor · fictional customer
- Example location
- Brighton, UK
- Issued / valid through
- 25 September 2026 / 25 October 2026
Read every amount in pounds
The table reproduces the fixture sent to the app exporter. Each amount is its quantity multiplied by the shown unit rate, rounded to pence. The largest line is Shelf material allowance at £613.20; that is a part of the total, not a standard price for work of this kind. Check the unit, quantity and scope together before comparing lines with a real supplier or subcontractor quote.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Wardrobe measurement and layout | 1 lump sum | £124.00 | £124.00 |
| Shelf material allowance | 7.3 metres | £84.00 | £613.20 |
| Hanging rod allowance | 3.7 metres | £47.20 | £174.64 |
| Bracket and fastener allowance | 1 lump sum | £148.00 | £148.00 |
| Shelf installation labour | 7.3 metres | £65.60 | £478.88 |
| Rod installation labour | 3.7 metres | £42.00 | £155.40 |
| Wall touch-up and clean-up | 1 lump sum | £116.00 | £116.00 |
| Subtotal / example total | £1,810.12 | ||
For a quick cross-check, shelf material allowance is 7.3 metres × £84.00 = £613.20, and hanging rod allowance is 3.7 metres × £47.20 = £174.64. The sum of all 7 line amounts is £1,810.12. The PDF's 0% tax input and zero markup are example settings; determine the correct inputs for your own work.
What this example assumes
The sample assumes suitable framing for the selected system. Additional blocking or wall repair should be assessed and added if needed.
Work outside the example: No wardrobe doors, new wall blocking, electrical work, full repainting or custom cabinetry.
The quantity basis matters. Where a product allowance differs from an installation quantity, the difference reflects this fictional layout or purchase plan and must be checked against the selected product. Existing conditions, safe access and any necessary approvals remain project decisions. Agree how changed measurements or discoveries will be recorded and priced before extra work begins.
View the app-exported PDF
The PDF was generated from this fictional project, with the exact line items, dates, customer and business details stated here. It is a completed example document for learning how an itemised estimate reads. Its prices are illustrative and are not current Brighton market rates.
Build an estimate for your own job
Start with a measured site record and the customer's selected finish or equipment. Replace all fictional quantities and rates, assign responsibility for supply and waste removal, and check that the exclusions describe the actual boundary. Review each extended amount, total and note in the PDF before sharing it.
- Measure shelf and rod runs.
- Confirm wall support.
- Select shelf depth and finish.
- List removal and wall-finish boundaries.
Read the matching built-in wardrobe shelving installation estimating guide for the measurement and scope decisions behind the example.
Common questions
Can shelving be priced by wardrobe measured area?
Measure the actual shelf and rod runs instead; the storage layout determines most quantities.
Are existing shelves removed?
Only if listed. This example assumes the space is ready for the selected system.
