EXAMPLE AT A GLANCE
This fictional Calgary, Alberta electrical outlet replacement example has 6 itemized costs and a C$1,558.90 total before tax or markup. The PDF, quantities, unit rates and scope assumptions match the table below.
Use this completed electrical outlet replacement document to see how a specific job becomes a client-facing estimate. The project, business, customer and amounts are fictional. For the six existing-location receptacles in Calgary, Alberta, the example uses the measured trade units shown in its PDF. Residential jobs may mix square feet, linear feet, counts and supplier units; keep each line’s measurement basis visible. Confirm the existing wiring, mounting and access with the person doing the work. Check which approvals or inspections apply at the project address before the estimate is treated as final. The figures are fictional CAD inputs, not a local price survey.
Project scope: Six existing-location receptacles
Replace six selected receptacles in existing suitable boxes and circuits. Include device allowance, faceplates, licensed installation labour, basic verification and cleanup. No new wiring, circuit correction or panel work; actual permits and qualifications must be verified.
- Example location
- Calgary, Alberta
- Prepared by
- Cedar & Beam Builders · fictional business
- Prepared for
- Jordan Taylor · fictional client
- Issued / valid through
- September 25 / October 25, 2026
Measure this work on the actual property before using any quantity. The illustration separates supplied products or materials from installation where the selection could change. A client should be able to compare each line with the agreed work, the selected products and the limits recorded in the notes.
The 6 itemized costs in Canadian dollars
Every row below is taken from the corresponding app-exported PDF fixture. Multiply the quantity by the unit rate to check the amount. These rates were chosen for this fictional example; they are not advertised prices or current averages for Calgary, Alberta.
| Work item | Quantity | Unit rate | Amount |
|---|---|---|---|
| Site review and circuit identification | 1 job | C$220.00 | C$220.00 |
| Receptacle device allowance | 6 each | C$41.00 | C$246.00 |
| Faceplate allowance | 6 each | C$10.15 | C$60.90 |
| Existing-device removal and replacement labour | 6 each | C$123.00 | C$738.00 |
| Basic verification and labeling | 6 each | C$32.00 | C$192.00 |
| Cleanup and old-device handling | 1 job | C$102.00 | C$102.00 |
| Subtotal / example total | C$1,558.90 | ||
Two calculation checks:
- Receptacle device allowance: 6 each × C$41.00 = C$246.00.
- Faceplate allowance: 6 each × C$10.15 = C$60.90.
The PDF shows a 0% tax entry, so the illustrated tax is C$0.00 and the total remains C$1,558.90. This only describes the example. Confirm the applicable tax treatment and any markup for the real job before issuing your estimate.
Assumptions that change the price
Record room, location, selected device style and any special requested function. Six devices are not necessarily interchangeable, so verify the schedule before ordering.
The example assumes suitable boxes, wiring and circuit capacity. A damaged box or unsuitable connection changes the work and should be documented before added work is priced.
Show devices and faceplates apart from labour. This keeps product upgrades visible and avoids presenting a device allowance as an all-inclusive electrical repair.
Outside this example: No new circuits, rewiring, panel work, box repair, concealed fault diagnosis or permit fees not specifically listed.
Confirm the existing wiring, mounting and access with the person doing the work. Check which approvals or inspections apply at the project address before the estimate is treated as final. An allowance is a stated placeholder, not a promise to cover all work discovered later. If a selected product, quantity or hidden condition changes, update the affected line and explain the revision before proceeding.
Download the actual app PDF
The linked PDF was exported from Estimates for this fictional Canadian project. It carries the project scope, customer, work items, quantities, CAD rates and subtotal used in this table, plus a short note on tax, markup and one key exclusion. The detailed exclusions above remain important when adapting the example. Preview every PDF page, including the final totals and note.
Use the structure for a real job
- Replace Calgary, Alberta and the example scope with the actual site and customer details.
- Measure the work and confirm the product schedule with the client.
- Replace every fictional CAD rate with your own labour, supplier and subcontractor inputs.
- Check exclusions, approvals, tax, markup and the document’s validity period for the real project.
- Preview the final PDF and recheck the total before sharing.
- List every device location and type.
- Inspect existing boxes and circuits.
- Verify qualified-trade and permit requirements.
- Define testing and correction boundaries.
Common questions
Can all outlets use one unit price?
Only when device type and existing conditions match. Count special devices and difficult locations separately.
Are wiring repairs included in a replacement quote?
Not in this example. Document any discovered issue and provide a revised electrical scope before correction.
For the planning steps behind this document, read the electrical outlet replacement estimating guide.
